Products Questions:

Posted by Mr Neil Stapleton on Monday, 27 February 2017

Question:

Will I need and air brick if I'm replacing an old gas fire. 1975 chalet house.

Answers:

  • Posted by Robin Harris on Monday, 27 February 2017
    I understand an stove or 5 kW or above will require an air vent / brick in the room, so not necessary for the GBS Mariner 4.
Posted by Miss Holly Faulkner on Tuesday, 10 January 2017

Question:

Is this multi fuel as in a review it states you can't burn coal

Answers:

  • Posted by Robin Harris on Tuesday, 10 January 2017
    Recommended fuels are dry, seasoned wood (logs) or anthracite / manufactured coal. Avoid household coal or pallet wood.
Posted by Mr Craig Goode on Thursday, 22 September 2016

Question:

How big is the firebox on the gbs mariner 4kw?

Answers:

  • Posted by Robin Harris on Thursday, 22 September 2016
    175mm wide x 200mm deep.
Posted by Mr Craig Goode on Monday, 6 June 2016

Question:

Hi Does the stove collar attach from inside the stove ? Thanks

Answers:

  • Posted by Robin Harris on Monday, 6 June 2016
    Stove flue collar attaches from the outside (top or rear outlet, interchangeable) and is sealed with fire cement.
Posted by Mr John Neve on Monday, 5 January 2015

Question:

What size flexi flue liner should I be using with this stove with my existing chimney, 5 inch or 6 inch? I note the stove flue outlet is only 4 inch according to the specs..

Answers:

  • Posted by Robin Harris on Monday, 5 January 2015
    For DEFRA Approved stoves, 5 Inch Flexible Flue Liner can be used. For non-DEFRA Approved stoves, 6 Inch Flexible Flue Liner should be used in order to comply with Building Regs.
    1 people found this answer helpfull.
Posted by Mr Alastair D Garrow on Tuesday, 2 December 2014

Question:

Can you tell me how far from a plasterboard wall covered in vermiculite board this would have to be?

Answers:

  • Posted by Robin Harris on Tuesday, 2 December 2014
    Recommended minimum clearances around the stove from non-combustibles (i.e. vermiculite board) are as follows: 50mm - 100mm at the rear of the stove 150mm either side 200mm above
Posted by mr anthony mitchell on Thursday, 30 October 2014

Question:

Does this have a british kite mark and how easy is it to buy a replacement grate.

Answers:

  • Posted by Robin Harris on Thursday, 30 October 2014
    Replacement parts are readily available. Stove is CE Approved to meet required European standards.
Posted by Robert Carr on Thursday, 16 October 2014

Question:

How thick must the hearth stone/plate be for this stove... which is dependent on whether the manufacturer has tested the stove and able to state whether their stove does raises the hearth temperature to over 100ºC or not.

Answers:

  • Posted by Adam Fowler on Thursday, 16 October 2014
    Hi, The manufacturer has not tested for this so by default it will need a 125mm constructional hearth. We do have a full range of stoves which have been tested to be acceptable, see them here www.gr8fires.co.uk/stoves/12mm-hearth-stoves
Posted by Mrs Diane Scott on Monday, 29 September 2014

Question:

Does this stove have an ash pan?

Answers:

  • Posted by Adam Fowler on Monday, 29 September 2014
    Hi, Yes it does.
Posted by Wayne on Thursday, 11 September 2014

Question:

Hi, Will this stove fit into a standard 16 x 22 opening? Thanks

Answers:

  • Posted by Robin Harris on Thursday, 11 September 2014
    Including recommended clearances, as per HETAS, you would require the following size opening for GBS Mariner 4 kW: Height: 26 inches Width: 25 inches Depth: 14.5 inches
Posted by roger carr on Friday, 5 September 2014

Question:

If I bought a mariner 4kw multifuel stove what would I need to purchase with it for complete installation

Answers:

  • Posted by Ronald Small on Friday, 5 September 2014
    It would be depend on whether the stove is going into an existing chimney or not. If it is it also depends on the condition of the chimney. Give us a call to discuss options.

Please login in to your account to place a question